Finishing quality is what separates a commodity gypsum board from a premium decorative panel. Our plasterboard spray coating machine is an automated production line designed to apply eco-friendly water-based latex paint onto the surfaces of both perforated gypsum boards and paper-faced gypsum boards, delivering a uniform, durable decorative finish at industrial throughput. Built for continuous factory operation, the line supports both single-coat and double-coat spraying modes, allowing manufacturers to switch between cost-efficient single-pass finishing and premium multi-layer protection without changing equipment.
Water-based latex systems have become the default choice for export-oriented building material producers. They release significantly lower volatile organic compounds than solvent-based alternatives, which helps factories meet tightening environmental regulations in the EU, North America and Australia. Low odour also means coated boards can be packed and shipped sooner, reducing warehouse dwell time. Our spraying line is engineered specifically around these coatings, with stainless-steel fluid paths, corrosion-resistant nozzles and controlled curing temperatures that protect the paint film from cracking or blistering.
The line runs as a continuous, sequential operation with a single control interface:
| Item | Specification |
|---|---|
| Applicable gypsum-board sizes | 600 × 600 mm, 600 × 1200 mm, 1220 × 2440 mm |
| Line running speed | 5–6 m/min |
| Installed power (single-coat spraying and drying section) | 125 kW |
| Control mode | Variable-frequency speed regulation |
These baseline figures cover the mainstream board formats used in ceiling and partition systems, from 600 × 600 mm lay-in tiles up to full 1220 × 2440 mm decorative panels. A working speed of 5–6 m/min supports stable, repeatable film quality while leaving headroom for future throughput increases, and the 125 kW installed power figure for the single-coat spraying and drying section keeps utility planning predictable. Variable-frequency speed regulation across the line allows operators to fine-tune conveyor, spray and drying speeds in step with one another, which is essential when changing board size or switching coating recipes.
| Station | Function | Automation Level |
|---|---|---|
| Spray booth (2 stages) | Water-based latex application, single or double coat | Fully automatic |
| Drying tunnel (2 stages) | Controlled thermal curing of each coat | Temperature & speed programmable |
| Combining unit | Board alignment and joining | Automatic |
| Stacking unit | Layer stacking with spacing protection | Automatic |
| Palletizer | Pallet build for transport | Robotic / gantry option |
| Packaging line | Wrapping and labelling | Semi to fully automatic |
This production line suits gypsum board plants, ceiling tile manufacturers and decorative panel processors looking to move finishing in-house. Because the framing is modular, the spraying and drying sections can be installed as an upgrade to an existing forming line, or supplied as a standalone coating workshop. Layout planning accounts for board width, throughput per shift, available floor space and local utility capacity, so the line fits both new greenfield factories and brownfield retrofits. Commissioning includes operator training on recipe setup, nozzle maintenance and colour changeover, helping your team reach stable output quickly.
Send us your board dimensions, target output per shift and preferred coating system, and our engineering team will propose a matched configuration with layout drawing and utility requirements. From single-coat entry-level setups to full double-coat automated lines with robotic palletizing, we build the coating section around your factory, not the other way around.
Finishing quality is what separates a commodity gypsum board from a premium decorative panel. Our plasterboard spray coating machine is an automated production line designed to apply eco-friendly water-based latex paint onto the surfaces of both perforated gypsum boards and paper-faced gypsum boards, delivering a uniform, durable decorative finish at industrial throughput. Built for continuous factory operation, the line supports both single-coat and double-coat spraying modes, allowing manufacturers to switch between cost-efficient single-pass finishing and premium multi-layer protection without changing equipment.
Water-based latex systems have become the default choice for export-oriented building material producers. They release significantly lower volatile organic compounds than solvent-based alternatives, which helps factories meet tightening environmental regulations in the EU, North America and Australia. Low odour also means coated boards can be packed and shipped sooner, reducing warehouse dwell time. Our spraying line is engineered specifically around these coatings, with stainless-steel fluid paths, corrosion-resistant nozzles and controlled curing temperatures that protect the paint film from cracking or blistering.
The line runs as a continuous, sequential operation with a single control interface:
| Item | Specification |
|---|---|
| Applicable gypsum-board sizes | 600 × 600 mm, 600 × 1200 mm, 1220 × 2440 mm |
| Line running speed | 5–6 m/min |
| Installed power (single-coat spraying and drying section) | 125 kW |
| Control mode | Variable-frequency speed regulation |
These baseline figures cover the mainstream board formats used in ceiling and partition systems, from 600 × 600 mm lay-in tiles up to full 1220 × 2440 mm decorative panels. A working speed of 5–6 m/min supports stable, repeatable film quality while leaving headroom for future throughput increases, and the 125 kW installed power figure for the single-coat spraying and drying section keeps utility planning predictable. Variable-frequency speed regulation across the line allows operators to fine-tune conveyor, spray and drying speeds in step with one another, which is essential when changing board size or switching coating recipes.
| Station | Function | Automation Level |
|---|---|---|
| Spray booth (2 stages) | Water-based latex application, single or double coat | Fully automatic |
| Drying tunnel (2 stages) | Controlled thermal curing of each coat | Temperature & speed programmable |
| Combining unit | Board alignment and joining | Automatic |
| Stacking unit | Layer stacking with spacing protection | Automatic |
| Palletizer | Pallet build for transport | Robotic / gantry option |
| Packaging line | Wrapping and labelling | Semi to fully automatic |
This production line suits gypsum board plants, ceiling tile manufacturers and decorative panel processors looking to move finishing in-house. Because the framing is modular, the spraying and drying sections can be installed as an upgrade to an existing forming line, or supplied as a standalone coating workshop. Layout planning accounts for board width, throughput per shift, available floor space and local utility capacity, so the line fits both new greenfield factories and brownfield retrofits. Commissioning includes operator training on recipe setup, nozzle maintenance and colour changeover, helping your team reach stable output quickly.
Send us your board dimensions, target output per shift and preferred coating system, and our engineering team will propose a matched configuration with layout drawing and utility requirements. From single-coat entry-level setups to full double-coat automated lines with robotic palletizing, we build the coating section around your factory, not the other way around.
